Multitech MTPSR1-202ST Podręcznik Użytkownika Strona 25
- Strona / 104
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 4 - ProxyServer Software
25
MTPSR1-202ST
Download Default Setup
This utility enables you to download the default settings, configured during installation, to the Proxy-
Server. If you are installing the software for the first time, you will download this setup at the conclu-
sion of the installation process, before operating the ProxyServer. If you have made changes to the
ProxyServer configuration and now want to revert to the default setup, you can do so through the
Proxy Server 2.01 program group.
Choose Download Default Setup to download the factory default settings. If the ProxyServer is
running, you will be queried to reboot. Click Yes to continue with the download. You will then be
presented with two dialogs including IP Setup and Default WAN Link Setup. These screens will
contain the original setup information. Click OK on each to accept the default settings, or make any
necessary changes, then click OK. When prompted, click OK again to proceed with the download.
The default setup will be written to the ProxyServer. The Fail indicator will remain On until the Proxy-
Server boot process is completed. This process may take a few minutes. When it finishes, you are
returned to Windows.
Download Firmware
This utility enables you to update the firmware of the ProxyServer, in conjunction with a repair or
receipt of a firmware upgrade. To download the firmware, choose Download Firmware from the
Proxy Server 2.01 program group, and the Open dialog box is displayed (if the ProxyServer is
running, you will be queried to reboot to update firmware; click OK to proceed, then the Open dialog
box will be displayed).
By default, the ProxyServer software will display the proper firmware from the Proxy Server folder.
Double-click on this file in the File Name list.
The Downloading Code dialog box is displayed, which includes a status bar to monitor the down-
load process. When the download is complete, the ProxyServer will reboot. When the Fail indicator
goes out, the reboot process is complete. This process will take several minutes. After rebooting, you
will be returned to Windows.
WAN Device Configuration
This utility opens the Print Console, a terminal emulation program, that will enable you to configure
the WAN port using AT commands from Appendix D.
Uninstall Proxy Server Configuration
Selecting Uninstall Proxy Server Configuration will completely remove all the components of the
Proxy Server 2.01 program group. Upon selecting this option, you will be queried for confirmation.
Click Yes to continue with the uninstall, or click No to abort.
Note: You will not be able to use the ProxyServer without Proxy Server Configuration. If you remove
the configuration components, you will have to reinstall the software. Refer to your ProxyServer
Quick Start Guide for installation instructions.
- ISDN ProxyServer 1
- User Guide 1
- Record of Revisions 2
- Contents 3
- Appendixes 4
- Glossary of Terms 4
- Chapter 1 - Introduction and 5
- Description 5
- Preview of this Guide 6
- Front Panel 8
- Back Panel 9
- Specifications 10
- Chapter 2 - Installation 11
- Introduction 12
- Unpacking 12
- Installation 13
- Adding Additional RAM 14
- Chapter 3 - Software Loading 15
- Call Control Parameters 17
- Data Control 17
- Loading your Software 18
- IP Port Configuration 20
- Before You Begin 24
- Download Default Setup 25
- Download Firmware 25
- WAN Device Configuration 25
- Main Menu 26
- Internet 27
- IP Setup 28
- WAN Port Setup 29
- US Parameters 30
- Europe Parameters 30
- Enabling the DHCP Server 32
- Enabling the Virtual Server 34
- Enabling Remote Servers 35
- Running Diagnostics 37
- WEB Management 47
- Chapter 6 - Service, Warranty 49
- Limited Warranty 50
- Tech Support 51
- MTPSR1-202-ST 52
- About the Multi-Tech BBS 53
- Reading a Message 54
- Leaving a Message 54
- Bulletins 54
- About CompuServe 55
- About the Internet 55
- Command Port Cable 58
- WAN Cable / LAN Cable 58
- 58
- Remote Configuration Cable 58
- Appendix B - Script Commands 59
- Example Script: 60
- Script Language Grammar 61
- Appendix D - AT Commands 64
- Command Function 64
- Command Implementation 66
- Switch Configuration Commands 66
- Data Call Commands 75
- S-Registers 77
- Table D-2. S-Register Summary 77
- S-Register Function 77
- Result Codes 80
- Table D-3. Result Codes 80
- Terse Verbose Definition 80
- Modes of Operation 81
- Making a Call 81
- Answering a Call 82
- Hanging Up 82
- Appendix E - TCP/IP 83
- Internet Protocol (IP) 85
- MTPSR1-202ST 100
Powiązane produkty i podręczniki dla Networking Multitech MTPSR1-202ST
(13 strony)
Networking Multitech FaxFinder FF240 Dokumentacja
(108 strony)
(108 strony)
Networking Multitech GFU19 Instrukcja Użytkownika
(152 strony)
(152 strony)
Networking Multitech MT5600SMI-XL34 Dokumentacja
(157 strony)
(157 strony)
Networking Multitech MTCBA-C-IP-N1 Dokumentacja
(330 strony)
(330 strony)
Networking Multitech MTCBA-G-U Dokumentacja
(23 strony)
(23 strony)
Networking Multitech MT5600SMI-32 Dokumentacja
(169 strony)
(169 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.130 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji