Multitech MTCBA-C-U Dokumentacja Strona 113
- Strona / 197
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 16 – Extended AT Commands in IS707.3
Multi-Tech Systems, Inc. CDMA AT Commands Reference Guide (PN S000294K) 113
Modulation Selection +MS
Description: The extended-format compound parameter is used to control the manner of operation of the modulation
capabilities in the DCE.
Values: <carrier>
manufacturer specific
<automode>
0 Disabled
1 enabled with V.8 or V.32bis Annex where applicable
<min_rate> & <min_rx_rate>
set to 0 if unspecified
<max_rate> & <max_rx_rate>
set to 0 if unspecified
Syntax: Command syntax:
AT+MS=[<carrier>[,<automode>[,<min_rate>[,<max_rate>[,<min_rx_rate>
[,<max_rx_rate>]]]]]]
Command Possible Responses
AT+MS?
Note: Display the parameter information.
+MS: V32B,1,1200,14400
Note: Command is valid
AT+MS=?
Note: Display the range of parameters
+MS: (V21,V22),(0,1,),(0,300-14400),(0,300-14400)
Note: Command is valid
AT+MS=V21,1,1200,2400,1200,2400
Note: Display the range of parameters
OK
Note: Command is valid
Modulation Automode Control +MA
Description: The extended-format compound parameter is a list of modulations that the DCE may use to connect with the
remote DCE in automode operation, for answering or originating data calls.
Syntax: Command syntax: AT+MA=[<carrier>[,<carrier>[,<carrier>[,…]]]]
Command Possible Responses
AT+MA?
Note: Display the parameter information.
+MA: V32, V32B
Note: Command is valid
AT+MA=?
Note: Display the range of parameters
+MA: (V32B,V32,V26B,V22B,V22,V21)
Note: Command is valid
AT+MA=V32
Note: Set to V32
OK
Note: Command is valid
Modulation Reporting Control +MR
Description: The extended-format numeric parameter controls whether the extended-format +MCR:<carrier> and
+MRR:<rate> intermediate result codes are transmitted from the IWF to the mobile station.
Values: <Val>
0 Disables reporting of modulation connection
1 Enables reporting of modulation connection (+MCR and +MRR are transmitted)
Syntax: Command syntax: AT+MR=[<Val>]
Command Possible Responses
AT+MR?
Note: Display the current setting.
+MR: 0
Note: Command is valid
AT+MR=?
Note: Display the range of setting.
+MR: (0,1)
Note: Command is valid
AT+MR=1
Note: Enable reporting.
OK
Note: Command is valid
- CDMA AT Commands 1
- Contents 3
- Chapter 1 – Introduction 9
- Terminology and Acronyms 10
- Chapter 2 – AT Command 13
- Features 13
- Attention AT 14
- Request IMSI +CIMI 15
- Capabilities List +GCAP 15
- Repeat Last Command A/ 15
- Phone Offline +CPOF 16
- Keypad Control +CKPD 17
- Clock Management +CCLK 17
- Ring Melody Playback +CRMP 17
- Ringer Sound Level +CRSL 18
- Subscriber Number +CNUM 18
- View Modem Timers +WTMR 19
- Chapter 4 – Call Control 20
- Hang-Up Command H 21
- Answer a Call A 22
- Remote Disconnection 22
- DTMF Signals +VTD, +VTS 23
- Automatic Answer S0 24
- Incoming Call Bearer +CICB 25
- Microphone Gain +VGT 26
- Volume Gain Control +VGR 26
- Echo Cancellation +ECHO 27
- TTY Mode +WTTY 28
- Chapter 5 – Network Service 29
- Band Preference +WBND 30
- Roam Preference +WRMP 31
- Change NAM Selection +WNAM 32
- Read Current NAM +WCNM 32
- Chapter 6 – SIM Card 35
- Operational Commands 35
- Enter PIN2 +CPIN2 36
- Change Password +CPWD 38
- Card Identification +CCID 38
- Chapter 7 – Short Messages 39
- Delete Message +CMGD 47
- Message Overwriting +WMGO 49
- Change SMS Status +WUSS 49
- Chapter 8 – Supplementary 51
- Services Commands 51
- Chapter 9 – Data Commands 55
- Cellular Result Codes +CRC 56
- Chapter 10 – V.24-V.25 58
- Set DCD Signal &C 59
- Set DTR Signal &D 60
- Set DSR Signal &S 60
- Back to Online Mode O 60
- Result Code Suppression Q 60
- DCE Response Format V 61
- Audio Loopback &T 61
- Echo E 61
- Save Configuration &W 62
- Chapter 11 – Phone Book 63
- Phonebook Read +CPBR 66
- Phonebook Search +CPBP 66
- Chapter 12 – Position 68
- Determination (GPS) 68
- IP Server Address +WMPC 73
- Chapter 13 - Specific AT 74
- Read GPIO Value +WIOR 78
- Write GPIO Value +WIOW 78
- Play Tone +WTONE 78
- Play DTMF Tone +WDTMF 79
- Hardware Version +WHWV 79
- Select Voice Gain +WSVG 80
- Status Request +WSTR 80
- Ring Indicator Mode +WRIM 81
- 32kHz Sleep Mode +W32K 81
- Software Version +WSSW 82
- CPHS Command +CPHS 83
- Reset +WRST 84
- Set Standard Tone +WSST 85
- Security PIN +WPIN 86
- Minute Alert +WMBP 87
- Chapter 14 - SIM ToolKit for 89
- RUIM Software Version 89
- Example: 91
- Chapter 15 – Provisioning AT 99
- Set IMSI +WIMI 100
- SID and NID +WSID 101
- Slot Cycle Index +WSCI 101
- Packet Dial String +WPDS 102
- Commit Changes +WCMT 104
- Read SID/NID Entries +WSNR 104
- Download PRL +DPRL 105
- Service Programming Example 106
- Chapter 16 – Extended AT 107
- Commands in IS707.3 107
- Select Pulse Dialing P 108
- Basic S-Registers S 108
- Error Control Report +ER 109
- Modulation Selection +MS 113
- V.18 Selection +MV18S 114
- Cellular Extension +CXT 115
- Configuration String +CFG 115
- Query Service +CAD 115
- Battery Charge +CBC 117
- Serving System +CSS 118
- Hang-up Voice +CHV 119
- Chapter 17 – Qualcomm 121
- Defined AT Commands for 121
- CDMA Operation 121
- Set DM Baud Rate $QCDMR 125
- SCRM’ing Selection $QCSCRM 126
- R-SCH IP Selection $QCMIP 127
- MIP Selection $QCMIPP 128
- Chapter 18 – TCP/IP App AT 133
- Commands 133
- Open Socket +WOSK 134
- Close Socket +WCSK 135
- Transmit Socket Data +WSTX 135
- Read Receive Data +WSRX 136
- Force Dormant Mode +WFDM 138
- IP Address Lookup +WDNS 139
- Display IP Address +WIPC 139
- PPP Session Status +WPPP 139
- Socket State Change +WSKS 140
- Received Socket Data +WSRX 141
- Socket Data Error +WSRE 141
- Chapter 19 – Reference 143
- Information 143
- Specific Error Result Codes 144
- Final Result Codes 145
- Intermediate Result Codes 145
- Parameters Storage 147
- TCP App Socket Status Events 150
- TCP App Socket Error Codes 150
- TCP App DNS Server Codes 150
- TCP App PPP Network Codes 150
- Phonebook UCS2 Unicode 152
- MuxLite Example 154
- Chapter 20 – Unsolicited AT 155
- Result Codes 155
- Key Press or Release +CKEV 156
- Mode Preference +COPS 158
- Incoming Call +CRING 158
- RxLev Indication +CSQ 159
- Incoming Call +RING 159
- Call Answered +WANS 159
- Call Connected +WCNT 160
- Call Ended +WEND 160
- Flash Indication +WFSH 161
- General Indicator +WIND 161
- Call Originated +WORG 162
- Roaming Indication +WROM 162
- Emergency Mode +WSOS 163
- Current NAM Change +WNAM 163
- Voice Mail Indicator +WVMI 164
- Power Save +WSPS 164
- Download PRL Status +DPRL 167
- Chapter 21 – AT Command 168
- Examples 168
- Incoming Voice Call 169
- Call Waiting 169
- Originate Data Call 169
- Originate Data Call Failure 169
- Short Message Examples 170
- GpsOne Examples 171
- AT Commands 175
- Read Message +CMGR 177
- List Message +CMGL 178
- Send Message +CMGS 179
- Facility Lock +CLCK 185
- Signal Quality +CSQ 185
- Boot URL +WBURL 187
- Trusted Domain +WTDMN 187
- Proxy Address +WDPXY 187
- IOTA Error +WOAE 188
- Please Retry +WOAR 188
- Display PRI Checksum +WSUM 189
Powiązane produkty i podręczniki dla Networking Multitech MTCBA-C-U
(10 strony)
Networking Multitech FaxFinder FF840 Dokumentacja
(116 strony)
(116 strony)
Networking Multitech MTCBA-G-UF1 Dokumentacja
(40 strony)
(40 strony)
(58 strony)
Networking Multitech FF200 Podręcznik Użytkownika
(169 strony)
(169 strony)
Gaggenau Akcesoria kuchenne i AGD podręczniki użytkownika
Zaczynanie od K
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji