Multitech CC4800 Instrukcja Właściciela

MultiModemManagerMR4800E Rack ControllerOwner’s Manual

MR4800E Owner’s Manual102.1 IntroductionThis chapter provides the information needed to install your MR4800E Rack Controller into a ModelCC4800 MultiM

Chapter 2 - Hardware Installation & Quick Starts112.3 Hardware Installation ProcedureTo install a MR4800E, perform the following steps.Step Proce

MR4800E Owner’s Manual122.6 Quick Starts2.6.1 MR4800E Quick StartFollow the steps below to configure your MR4800E.1. Power down your CC4800 rack.2. In

Chapter 2 - Hardware Installation & Quick Starts132.7 Supervisor Console Configuration1. Set up security accounts by using the Security DB Editor

MR4800E Owner’s Manual14

MultiModemManagerChapter 3 - Hardware Operation

MR4800E Owner’s Manual163.1 IntroductionThe operation of the MR4800E consists of observing the front panel indicators (refer to Chapter 5). Ifthe opt

Chapter 3 - Hardware Operation173.4 SNMP InterfaceThe MR4800E can be controlled/monitored using SNMP through the MultiModemManager or a thirdparty SNM

MR4800E Owner’s Manual183.6 Telnet InterfaceTelnet is an Internet standard protocol that allows the remote login between two systems connectedto a TCP

Chapter 3 - Hardware Operation193.8 FTP InterfaceFTP (File Transfer Protocol) is an Internet standard protocol that allows the transfer of files betwe

MR4800E Rack ControllerOwner’s ManualP/N 82042403, Revision DThis publication may not be reproduced, in whole or in part without prior expressed writ

MR4800E Owner’s Manual20

MultiModemManagerChapter 4 - Commands

MR4800E Owner’s Manual224.1 Parameter DescriptionsHere is a description of the parameters used in the command descriptions that follow.PathnameDescrip

Chapter 4 - Commands234.2 Commands Listed by FunctionIn this section, the commands are listed alphabetically by function. The functions are: Display

MR4800E Owner’s Manual24FileCommand Name Parameters Descriptioncat Pathname Display the contents of an ASCII text filecd, chdir Pathname Change to the

Chapter 4 - Commands25SecurityCommand Name Parameters Descriptionlo, logout None Logs you off of the system so next user hasto login to get accesspass

MR4800E Owner’s Manual264.3 Commands Listed by Security LevelIn this section, the commands are listed by security level. The security levels are: Gu

Chapter 4 - Commands27 Operator (cont.)Command Name Parameters Descriptiongetfkey4 None keys used when on-line with a devicegetmodems Device Displays

MR4800E Owner’s Manual284.4 Command ReferenceThis section has all the commands listed alphabetically with an expanded explanation.See Section 4.1 for

Chapter 4 - Commands29!aParameters: The letter (or letters) of the command to search for.Description: Repeats the command whose beginning letter (or l

ContentsChapter 1 - Introduction & Description1.1 Introduction ...

MR4800E Owner’s Manual30cd, chdirParameters: PathnameDescription: Change to the specified directory. The cd command sets the current working director

Chapter 4 - Commands31copy, cpParameters: Pathname1 & Pathname2Description: Copy a file from Pathname1 to Pathname2. Copy the file indicated by P

MR4800E Owner’s Manual32dir, lsParameters: PathnameDescription: Display the contents of a directory. The dir command will list the files of the direc

Chapter 4 - Commands33downloadParameters: PathnameDescription: Download a file from the MR4800E. The download command will allow you to movefiles off

MR4800E Owner’s Manual34getcallsParameters: DeviceDescription: Displays call traffic for Device. If there is no parameter, call traffic is listed for

Chapter 4 - Commands35getfaultsParameters: Device. If there is no parameter, then system faults are listed.Description: Displays faults for Device.

MR4800E Owner’s Manual36getfkey1, getfkey2, getfkey3, getfkey4Parameters: NoneDescription: Displays the current configure values for the on-line funct

Chapter 4 - Commands37getmodemsParameters: DeviceDescription: Displays the current status for the modems indicated by Device. If there is noparameter

MR4800E Owner’s Manual38getreadcommunityParameters: NoneDescription: Displays the Read community settings.Security: SupervisorExample:[0] A:\MMM # get

Chapter 4 - Commands39gettrapParameters: NoneDescription: Display the configured trap address. The gettrap command displays the default trap IPaddres

ivChapter 6 - Service, Warranty, & Tech Support6.1 Service...

MR4800E Owner’s Manual40lo, logoutParameters: NoneDescription: Logs you off of the system so next user has to login to get access. The logoutcommand

Chapter 4 - Commands41onlineParameters: DeviceDescription: Goes on-line with a device to check configuration information and firmware versioninformati

MR4800E Owner’s Manual42oosset, osParameters: DeviceDescription: Set the specified device Out of Service. The os command will set the Out Of Servicef

Chapter 4 - Commands43rd, remdirParameters: PathnameDescription: Remove directory. The rd command will delete the directory indicated by thepathname.

MR4800E Owner’s Manual44rmSee del.rsSee reset.se, setenvironParameters: NoneDescription: Change the environment values for the MR4800E. The se comman

Chapter 4 - Commands45securityParameters: NoneDescription: Allows the modification of a subordinate security levels username and password. Thesecurit

MR4800E Owner’s Manual46setconfigParameters: Pathname & DeviceDescription: Associates a configuration file with a particular device.Security: Oper

Chapter 4 - Commands47setfkey1, setfkey2, setfkey3, setfkey4Parameters: Command StringDescription: Configures the current values for the on-line funct

MR4800E Owner’s Manual48setsendtrapParameters: on, offDescription: Configure the MR4800E controller card to send traps or not. This command can beused

Chapter 4 - Commands49setwritecommunityParameters: NoneDescription: Change the Write community settings.Security: SupervisorExample:[0] A:\ # setwrite

MultiModemManagerChapter 1 - Introduction & Description

MR4800E Owner’s Manual50updateParameters: [Pathname {Device}]Description: Updates the controller and modem firmware. The update command allows you t

Chapter 4 - Commands51useridParameters:NoneDescription: Will prompt you for old, new, and new user id. The userid command allows you tochange your us

MR4800E Owner’s Manual524.5 Error MessagesWhen you receive an error message when executing a command be sure to check the commandspelling. Do you hav

Chapter 4 - Commands53ERROR: Password not changedPossible Cause:The old password does not match the stored password; the new password is invalid; or t

MR4800E Owner’s Manual54

MultiModemManagerChapter 5 - Troubleshooting

MR4800E Owner’s Manual565.1 IntroductionThis chapter provides the information needed to identify and fix problems with the MR4800E.Problems can be obs

Chapter 5 - Troubleshooting575.4 Ethernet Status LEDsThe MR4800E front panel contains four Ethernet status LEDs. Each LED is described below.LED Colo

MR4800E Owner’s Manual58

MultiModemManagerChapter 6 - Service, Warranty, & Tech Support

MR4800E Owner’s Manual61.1 IntroductionThis manual is intended to provide the information needed for field installation of a Multi-TechMR4800E Rack Co

MR4800E Owner’s Manual606.1 ServiceIn the event that repair service is required, you may send your modem to our Mounds View factory inthe USA. Produc

Chapter 6 - Service, Warranty & Tech Support616.3 The Multi-Tech BBSFor customers who do not have Internet access, Multi-Tech maintains a bulletin

MR4800E Owner’s Manual626.4 On-Line Upgrade via Flash PEROM and FLASHPROSoftwareThe MR4800E Rack Controller has a Flash PEROM (Programmable and Erasab

Index63IndexSymbols!! ... 28!a ...

MR4800E Owner’s Manual64Ooc ... 40oosclear...

Chapter 1 - Introduction & Description71.4 SpecificationsThe MR4800E is designed to meet the following specifications:• contains one Motorola MC68

MR4800E Owner’s Manual8

MultiModemManagerChapter 2 - Hardware Installation & Quick Starts